tiresheet81

How to Replace a Kia Sportage Replacement Key The key of many Kia models comes with a keyless entry system built in. This key typically resembles an remote control, and can be changed by a new one purchased from an Kia dealer or a locksmith. Key fobs are prone to malfunction for a variety of reasons, such as an empty coin battery, worn buttons signals, signal interference, water damage, and a defective receiver module. Here are some suggestions on how you can get your Kia Sportage replacement key to work again. How to replace the remote key or smart key? It doesn't matter if your Kia comes with an intelligent key, remote key push-to-start keys, or a standard non-transponder key made of metal the battery in these keys will eventually require replacement. This is particularly true if the car displays a message telling that the smart or remote key has low battery power. Fortunately, it's an easy procedure. To replace the keyfob battery remove the mechanical key from the slit that is located at the back of the fob. Then, pull the cover off. Inside the key fob, there will be a small screw that holds the battery in its place. Remove the old battery by removing the screw with a small screwdriver. Install the new battery and then close the cut on the key fob. Test the key fob by pressing the lock and unlock buttons. It's okay If the doors lock and unlock as expected. You can now use the hands-free feature to lock and unlock your Kia whenever your fingers become cold or when you need to do some errands in Brandon. Note: Some key fobs might need to be programmed (transponder chips or smart keys). This requires a programming machine that is only available to the locksmith who works for the automotive dealer. Other keys (non-transponder metal keys) do not require programming. If you need to reprogramme your key, it is necessary to record the key code number on the tag for the key code. How do you replace a dead battery? If the Kia key fob doesn't respond when you press the lock/unlock button, it's likely that the battery is low. A low battery may cause other issues, like the check engine light appearing or the engine not cranking correctly. Fortunately replacing the battery on the key fob is a relatively easy DIY project that requires only a few basic tools. Before you begin be sure that your vehicle is off and all doors are shut. Find the small metal or plastic piece that is on the bottom of your key fob and play with it until a metallic key slips out. You can then insert the key in the handle on the door of your driver to unlock your car. To replace the key fob's battery, remove the cover from the back and use a pry bar tool to loosen the latch that holds the black negative battery cable. Remove the old battery, and then orient the replacement battery so that its “+” side is facing you and the “–” negative side is facing the fob's electrical contacts. Avoid using kia picanto key fob replacement when pushing the new CR2032 into place to avoid damage or bending the metal contacts. Once the new battery is installed and the key fob is turned on, turn it off and then turn it on in the ignition repeatedly until the door locks. Then, you can test your Kia key fob and see whether it's working again. How to replace a smart key Depending on the model of your Kia Sportage, you may have an ordinary key fob or a smart key. The smart key has an embedded mechanical key blade while the standard key fob does not. Both kinds of key fobs come with batteries inside that eventually will need to be replaced. This is a straightforward process which takes just two minutes. Before you begin before you begin, make sure that you are on a level surface with adequate lighting and that the Kia is off. Also, remember that there are tiny pieces inside the fob that can fall out if you are not cautious. The first step is to find the small release button on the backside of the fob. It can be an oval silver button or a rectangular slot. After pressing this button, the mechanical key blade will be released and you can then open the key fob. Once you have the key fob open, you can simply take out the old battery and replace it. The new battery is the CR-2032, and it can be bought from a local or online auto parts store. After you've finished you should be able to lock and unlock your car using your key fob – even if the engine isn't running! How do you replace the mechanical key The Kia key fob is an amazing convenience that allows us to lock and unlock our car at the press of a button. As with all devices that is used, the Kia key fob can have issues at times. Luckily, there are ways to fix these issues and ensure that our key fobs are in good working order in the long run. A dead or low-quality battery is among the most frequently encountered issues. This could cause your device to stop working or work intermittently. If this is what you are experiencing you should replace the battery a new one. If this does not solve the problem, use a flathead screwdriver standard to push the fob's casing made of plastic open. Be careful not to harm any internal components or scratch the plastic. When the battery is open, carefully take off the battery you have been using and replace it with a brand new one. After the new battery has been put in, close and open the doors with the mechanical key (every kia fob has an emergency mechanical key that can fit into the slot). Test the key fob to make sure it is working properly. If the device isn't working, contact an authorized locksmith or dealer to help resolve the issue. To avoid future lockouts, ensure that you have an emergency key that can work on all trunk and door cylinders.